Javascript DHTML Drop Down Menu Powered by dhtml-menu-builder.com
 
Acrylic Polymer Emulsions for Waterproofing, Construction Chemicals, Paint Emulsions,
Bopp Tape Adhesives, Waterbased Printing Inks
 
 

Nano-Acrylics for Paints, Coatings on Metal, Wood

 
Concrete Sealer Primer Kamicryl-CS0002
 
Description/Use Kamicryl-CS0002 is a newly developed premium water base concrete sealer primer utilizing the latest available technology. The coating incorporates water base pure acrylic and polyurethane technology offering superior adhesion and early water resistant properties. Excellent adhesion to difficult substrates including cementitious, glass and glazed tiles, Paver Blocks, Wood, Metals, Plastics, etc.
 
Areas of Use Designed to be used as a primer for cementitious substrates
including driveways, pathways, patios and garage floors.
   
Special Features * Excellent wet look and minimal colour change to substrate
* Excellent early water resistance
* Excellent wet and dry adhesion properties
* Low VOC at less than 38g per Liter
* Excellent exterior durability and low yellowing
* Excellent dirt and stain resistance
   
Thinning Not required – ready for use
   
Method of Application Brush or spray. Satisfactory with most equipment. Observe the State Spray Painting Regulations.
Do not apply if temperature is below 10ºC or likely to fall below 10ºC and below the dew point temperature during drying.
Do not apply if rain is expected or in extreme hot dry conditions. Do not apply if the substrate temperature is 10ºC or less.
   
Drying(25º C & 50% R.H.) Dry to touch - 30 Minutes
Recoatable - 3 to 4 Hours
   
Coverage Approximately 12 sqm/Lt/Coat
Recommend 1 to 2 coats for optimum performance and durability Coverage will vary depending on the profile and porosity of the surface.
Clean Up Water
   
Surface Preparation  
Green Concrete Allow concrete to fully cure as required. Remove all loose material and wash with clean water and allow to dry.
  Due to the numerous coating additives used in concrete mixture by numerous suppliers, it is necessary to perform numerous adhesion spot test checks of reasonable size. Apply the coating and allow a minimum 48 hours to dry and perform an adhesion test according to AS/NZ1580.408.2 - Knife Test and AS/NZ1580.408.4 - Cross –Cut.
Health & Safety * Keep out of reach of children
* Wear protective clothing
* Ensure good ventilation if using inside
* Do not breathe vapour or spray
* Do not smoke
* Wear eye protection
* Store in a cool place
First Aid Eye Contact – rinse with cold running water for 10 to 15 minutes.
Seek medical attention if irritation persists.
If Swallowed- drink large amounts of water and seek medical attention.
   
Environment Do not tip unused paint or washings down drains
Dispose of waste using authorized collection procedures.
Disposal When cleaning up after painting, ensure that paint does not get into Gutters or drains as it may contaminate waterways.
Do not reuse empty can, this can is recyclable. Check with your local Council to see if it is participating in a steel can recycle programme.
 
 
<< BACK
 
   

Acrylic Polymers for Construction
Chemicals

Acrylic Emulsions for Paints
Acrylic Emulsions for waterbased inks
Water Based Polyurethane Dispersions (PUD's)
Nano-Acrylics for Paints, Coatings on Metal, Wood
Hygiene Coatings for Cleanrooms
Waterproofing Construction Chemicals
Self Priming Direct to Concrete Emulsions
Advanced Specialty Architectural Emulsions (DTM)
Self Crosslinking Emulsions
Timber Emulsions
Over Print Varnish Industry
Texture Coatings & Roof Pointing Emulsions
Elastomeric & Waterproofing Emulsions
Wood Paints
 
Home - About Us - Products - Clientele - Enquiry - Contact Us Designed & Hosted by : MID   Promoted by : GID