Javascript DHTML Drop Down Menu Powered by dhtml-menu-builder.com
 
Acrylic Polymer Emulsions for Waterproofing, Construction Chemicals, Paint Emulsions,
Bopp Tape Adhesives, Waterbased Printing Inks
 
 

Nano-Acrylics for Paints, Coatings on Metal, Wood

 
Concrete Sealer Topcoat Kamicryl-CS0003
 
Description/Use Kamicryl-CS0003 is a newly developed ultra premium water base concrete sealer utilizing the latest available technology. The coating incorporates 100% water base polyurethane technology offering superior overall properties and performance.
   
Areas of Use Designed to be used for topcoat application over epoxy coatings on concrete substrates, or when used in conjunction with Kamicryl- CS0002 Primer, the system is highly durable and suitable for medium trafficable driveways, pathways, car parks, and garage floors.
   
Special Features * Excellent wet look and minimal colour change to substrate
* Excellent early water resistance
* Excellent chemical and solvent resistances
* Low VOC at less than 22g per Liter
* Excellent exterior durability and low yellowing
* Excellent dirt and stain resistance
   
Thinning Not required – ready for use
   
Method of Application Brush, roller or spray.
Satisfactory with most equipment. Observe the State Spray
Painting Regulations.
Do not apply if temperature is below 10ºC or likely to fall
below 10ºC
Do not apply if rain is expected or in extreme hot dry
conditions.
   
Drying(25º C & 50% R.H.) Dry to touch - 30 Minutes
Recoatable -3 Hours
   
Coverage Approximately 16 sqm/Lt/Coat
Recommend 2-3 coats for optimum performance and
durability Coverage will vary depending on the profile
and porosity of the surface.
   
Surface Preparation  
Green Concrete Allow concrete to fully cure as required. Remove all loose material and wash with clean water and allow to dry.
  Due to the numerous coating additives used in concrete mixture by numerous suppliers, it is necessary to perform numerous adhesion spot test checks of reasonable size. Apply the coating and allow a minimum 48 hours to dry and perform an adhesion test according to AS/NZ1580.408.2 - Knife Test and AS/NZ1580.408.4 - Cross – Cut.
Health & Safety * Keep out of reach of children
* Wear protective clothing
* Ensure good ventilation if using inside
* Do not breathe vapour or spray
* Do not smoke
* Wear eye protection
* Store in a cool place
First Aid Eye Contact – rinse with cold running water for 10 to 15 minutes.
Seek medical attention if irritation persists.
If Swallowed- drink large amounts of water and seek medical attention.
Environment Do not tip unused paint or washings down drains
Dispose of waste using authorized collection procedures.
Disposal When cleaning up after painting, ensure that paint does not get into Gutters or drains as it may contaminate waterways.
Do not reuse empty can, this can is recyclable. Check with your local Council to see if it is participating in a steel can recycle programme.
 
 
<< BACK
 
   

Acrylic Polymers for Construction
Chemicals

Acrylic Emulsions for Paints
Acrylic Emulsions for waterbased inks
Water Based Polyurethane Dispersions (PUD's)
Nano-Acrylics for Paints, Coatings on Metal, Wood
Hygiene Coatings for Cleanrooms
Waterproofing Construction Chemicals
Self Priming Direct to Concrete Emulsions
Advanced Specialty Architectural Emulsions (DTM)
Self Crosslinking Emulsions
Timber Emulsions
Over Print Varnish Industry
Texture Coatings & Roof Pointing Emulsions
Elastomeric & Waterproofing Emulsions
Wood Paints
 
Home - About Us - Products - Clientele - Enquiry - Contact Us Designed & Hosted by : MID   Promoted by : GID