Javascript DHTML Drop Down Menu Powered by dhtml-menu-builder.com
 
Acrylic Polymer Emulsions for Waterproofing, Construction Chemicals, Paint Emulsions,
Bopp Tape Adhesives, Waterbased Printing Inks
 
PRODUCTS
 
High Build Speaker Cabinet Texture Coating
 
DuraTex High Build is a Black Satin, high performance protective texture coating that has tremendous adhesion to wood and other substrates. It can be spray applied to create a tough, beautiful, weather resistant, HIGH BUILD and easily maintained texture surface. DuraTex HB was designed to provide beauty and protection to wood speaker cabinets, road cases and other applications. DuraTex HB is a blend of highly technical polymers, and special LOW V.O.C coalescents for creating beautiful high relief spatter textures. DuraTex HB requires no special primers and is easily applied with Hopper Gun, HVLP Pressure pot, brush or textured roller.
TECHNICAL DATA:
% Solvent by Wt: 4.37%
Viscosity: 8-10 Kcps
Solids by Weight: 58%
V.O.C.: 0.72#/Gal. (87g/L) (VERY LOW VOC)
Hardness: Tg +30°C
Solids by Volume: 51%
 
SURFACE PREPARATION: All substrates must be clean and dry with no oils, silicones, waxes or
other contaminants. Sand surfaces before application and remove all sanding residue. Bare wood surfaces need not be primed; however a base coat of DuraTex HB can be applied as its own primer.
 
APPLICATION: Apply DuraTex HB spray grade by Hopper Gun, pressure pot or airless spray system in a complete even coat to the entire surface to completely seal and protect the surface. Once the base coat is dry, apply a spray texture coat by lowering the air break-up pressure. Spray pressures will be dependent on the type of spray equipment being used. Test the spray application technique first on a piece of cardboard and note pressure settings needed to accomplish the finish desired. Higher air pressure=smaller dots. Lower air pressure produces larger dots. Higher fluid pressure + Higher air pressure produces a smoother, orange peel surface.
Allow all materials to dry thoroughly through air drying or forced drying in a baking oven. Do not exceed temperatures of 150° F for drying. Heating speeds up the curing process of DuraTex HB but normal air drying will accomplish the same finished result over time. (Oven heating is optional, but facilitates rapid production throughput.) Do not apply this product when surface temperature or ambient will be below 65° F or with Relative Humidity levels above 70%.
STORAGE: To store containers that have been previously opened, spray a fine mist of water onto the coating surface in the container before resealing the lid. This raises humidity levels in the container and can help prevent the product drying or skinning over in the container.
HMIS RATINGS: HEALTH 1 FLAMMABILITY 0 REACTIVITY 0
PERSONEL PROTECTION: HANDLING B APPLICATION G
CAUTIONS: Keep from freezing.use only with adequate ventilation.wear niosh approved organic vapor cartridge mask when applying or sanding in confined area. Do not take internally. Close container after each use. Keep out of the reach of children!Avoid eye and skin contact. Wear goggles. Shelf life at least one year when stored at 750 F in original unopened containers.
 
 
   

Acrylic Polymers for Construction
Chemicals

Acrylic Emulsions for Paints
Acrylic Emulsions for waterbased inks
Water Based Polyurethane Dispersions (PUD's)
Nano-Acrylics for Paints, Coatings on Metal, Wood
Hygiene Coatings for Cleanrooms
Waterproofing Construction Chemicals
Self Priming Direct to Concrete Emulsions
Advanced Specialty Architectural Emulsions (DTM)
Self Crosslinking Emulsions
Timber Emulsions
Over Print Varnish Industry
Texture Coatings & Roof Pointing Emulsions
Elastomeric & Waterproofing Emulsions
Wood Paints
 
 
Home - About Us - Products - Clientele - Enquiry - Contact Us Designed & Hosted by : MID   Promoted by : GID